Comments In contrary to some of the user’s comments below, this printer works well with the “hl” driver, a driver based on “ljet4” but preceeding the job with Brother-specific PJL commands, especially the one to set the resolution as shown below. Heat roller gear projection Heat roller bearing This blinking does not stop until you have installed a new toner cartridge. The printer automatically recovers from most errors, but it may also be necessary to reset the printer with the control panel button. The HL printer has 4 Mbyte of standard memory and a slot for optional additional memory. Cancel Printing If you press the button during printing, the printer immediately stops printing and ejects the paper. Improving the print quality Caution If the Drum LED is on you can clear a print quality problem by replacing the drum unit with a new one.

Uploader: Gror
Date Added: 26 September 2005
File Size: 41.8 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 62977
Price: Free* [*Free Regsitration Required]

A 4 Check the result that the printer reported and click the A, B or C button depending on the result.

Brother HL 1240 – B/W Laser Printer Service Manual

The peak figure of brother hl-1240 laser printer consumption is worked out excluding brothher current value. GPL free software User pritner If the replacement plug is intended to take a fuse then fit a fuse with the same rating as the original.

The RSA brother hl-1240 laser printer have been correctly set at the factory for Apple Macintosh computers, you do not need to change the settings.

LSB is a trademark of the Linux Foundation. If it is load paper.

Print speed may vary depending on interface type, emulation, processing power of the computer, memory allocated to the print job, paper size and graphic quality. APPENDIX How to Read the Maintenance Information The maintenance information such as the frequency of brother hl-1240 laser printer parts replacement or paper jam is known from the digit numbers shown in the lower line on the right below the drum unit life bar.

Last Drivers  PROSAVAGEDDR 420 430 DRIVERS

If you are using an interface switching device, remove it and printeg your computer directly to your printer and try again. The use of very thin or very thick paper is not recommended. If toner cartridges are left unpacked for a long period of time, the toner brother hl-1240 laser printer is shortened.

Check that the printer cable is not damaged or broken. Check also that the cable is connected to brother hl-1240 laser printer correct interface connectors of both the printer and PC. According to the printout quality it is based on the “ljet4” Ghostscript driver.

Manuals | HL | United States | Brother

Cleaning with volatile liquids such as thinners or benzene will damage the surface of the printer. Check the test page printed correctly.

You need a serial interface cable with an 8-pin, DIN-type connector to connect your printer and computer. Hold down the control panel button and turn on the power switch.

Brother HL-1240 A4 Mono Laser Printer

Joint spring Development joint Link Drum unit Position of smudge on the drum 94mm interval Enter text from picture: As a Gold Certified Independent Software Vendor ISVSolvusoft is able to provide the highest level of customer satisfaction through delivering top-level software and service solutions, which have been subject to a rigourous and continually-audited approval process by Microsoft. The glue that is used might cause damage to the printer. The brother logo is a registered trademark of Brother Industries, Ltd.


In the case of ordering parts, it needs mentioning the following items: Page APPENDIX How to Read the Maintenance Information The maintenance information such as the frequency of consumable parts replacement or paper jam is known from the digit numbers shown brother hl-1240 laser printer the lower line on the right below the drum unit life brother hl-1240 laser printer.

Brother HL Toner Cartridges

llaser Printer supports direct text printing with the ‘us-ascii’ brother hl-1240 laser printer. Place the drum unit assembly containing the old toner cartridge on a flat, horizontal surface, and pull the toner cartridge out of the drum unit assembly while pushing the lock lever down with your right hand.

Be sure to remove all ul-1240 covers and the base plate before removing the paper pick-up roller ASSY. To prevent direct exposure to the laser beam, do not try to open the enclosure of the laser unit. Install the SIMM into the slot at an angle and then push it gently towards the brother hl-1240 laser printer until it clicks into place. If the Drum LED is on, brother hl-1240 laser printer indicates the drum unit is nearly at the end of its life.

Bbrother paper Is the specified weight of the Recommend to use the specified recommended paper being Click the Next button.

A-4 Parallel Interface Specifications Do not remove the drum unit assembly with additional force at this time if you cannot remove it easily.